SpeedyBee F405 V3 3-6S 50A FC&ESC 30X30 Flight Controller 4in1 FPV Freestye

Description: SpeedyBee F405 V3 BLS 50A StackSo so many cool features,at an unbelievable price!$69.99 for a Bluetooth 50AStack? That's ridiculousI know right? With only $69.99, you will get an STM32F405 FC(better than F411), onboard 4-level battery life indicator, 4GBBlackbox SD card slot for your flight logs, 4 groups of LED strip pads,complete with a DJI plug* for your digital quad, and built-in Bluetoothfor wireless configuration on the SpeedyBee app.Don't forget about the powerful 50A 4-in-1 ESC, built with TVSprotective diode + Japan made TDK SMT capacitors + external1000uF low ESR capacitor, everything is for durable build andsmooth flight.All of that for only $69.99! Top-shelf spec at a crazy low price, whatare you waiting for?* The DJI Air Unit plug is completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.Configure your FC and ESCvia BluetoothWith SpeedyBee app, turn your phone into an all-in-oneFC configurator and tune your quad anytime, anywhere.Experience wireless, fully configurable ESC experience withSpeedyBee app.Powerful Real 50A 4-in-1 ESC!Built with the robust BB21 MCU and large motor pads for easysoldering. Built with Japan made TDK filtering SMT capacitors +onboard TVS protective diode, brings smooth flight experience.Real 50A output, ready for your baddest 6S motors.Forgot your LiPo checker?Just look at the FC!Built with a 4-level LED battery indicator, now you can flyanywhere worry-free - even without your lipo checker! * 1 light constantly on: battery level 10-25%1 light blinking: battery level < 10%8 motors output for X8/Y6/fixed-wingsYou could use this stack to build your X8 drones, Y6 drones orfixed wings. Forget about crawling through your massive buildjust to plug in that USB cable. Just take out your phone toconfigure everything in the SpeedyBee app.Change motor directionswirelessly!Finishing your latest build? Just replaced your motor after a crash?Take your smartphone out, and configure your motor directionwirelessly with the latest SpeedyBee app. Works for allBLHeli32 / BLHeli_S / BlueJay ESCs.4 sets of LED pads withsimple switchingNeed more visibility at night? Just solder up your LED strips*and blaze the darkest trail you can find. With just one tap on the BOOT button, you can cycle through all different LED presets**and pick the one you love!* LED strips could be purchased here**Or long press the boot button to switch to Betaflight LED mode1000uF Low ESR capacitor +TVS protective diode =Extra protectionThe ESC is built with TVS protective diode to absorb the voltagespike when you plug in the battery, or during crashes that blockyour props.We also provide a humongous 1000uF low ESRcapacitor, ensuring clean data from the gyro to the FC.And packaged with moreuseful features● Built-in barometer for accurate height calculation● SD Card slot can support up to 4GB Blackbox data*● Dedicated DJI Air Unit connector for a quick digital build● 9V 2A + 5V 2A individual BECs● 4 x UARTs for your receiver + VTX + camera + GPS.● Power your GPS with a USB cable - no battery needed. No extra heat, no worries.● 22mm cutouts for FPV camera in your tight build*Betaflight firmware requires the type of the microSD card to beeither Standard (SDSC) or High capacity (SDHC), so extendedcapacity cards (SDXC) are not supported(Many high-speed U3 cardsare SDXC). Also the card MUST be formatted with the FAT16 or FAT32(recommended) filesystems. So, you could use any SD card less than32GB, but the Betaflight can only recognize 4GB maximum.We suggest you use this 3rd party formatting tool and choose'Overwrite format' then format your card. Also check out here forthe recommended SD cards or buy the tested cards from our store.Dimensions Wiring Diagram SpecificationsProduct NameSpeedyBee F405 V3 30x30 Flight ControllerMCUSTM32F405IMU(Gyro)BMI270USB Port TypeType-CBarometerBuilt-inOSD ChipAT7456E chipBLE BluetoothSupported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)WIFINot supportedDJI Air Unit Connection WayTwo ways supported: 6-pin connector or direct soldering.6-pin DJI Air Unit PlugSupported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.Blackbox MicroSD Card Slot*Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC), so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the card MUST be formatted with the FAT16 or FAT32 (recommended) filesystems. So, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose 'Overwrite format' then format your card. Also check out here for the recommended SD cards or buy the tested cards from our store.BetaFlight Camera Control PadYes(CC pad on the front side)Current Sensor InputSupported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0.Power Input3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)5V Output9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 2A.9V Output2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 2A.3.3V OutputSupported. Designed for 3.3V-input receivers. Up to 500mA current load.4.5V OutputSupported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.ESC SignalM1 - M4 on bottom side and M5-M8 on front side.UART6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6ESC TelemetryUART R5(UART5)I2CSupported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.Traditional Betaflight LED PadSupported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.BuzzerBZ+ and BZ- pad used for 5V BuzzerBOOT ButtonSupported.[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.RSSI InputSupported. Named as RS on the front side.Smart Port / F.PortNot supportedSupported Flight Controller FirmwareBetaFlight(Default), INAV (INAV firmware can only use Multishot (recommended) and OneShot125. Please note that DShot is not supported.)Firmware Target NameSPEEDYBEEF405V3Mounting30.5 x 30.5mm( 4mm hole diameter)Dimension41.6(L) x 39.4(W) x 7.8(H)mmWeight9.6gProduct NameSpeedyBee BLS 50A 30x30 4-in-1 ESCFirmwareBLHeli_S JH50Wireless ConfigurationFull Configuration Supported in the SpeedyBee appPC Configurator Download Linkhttps://esc-configurator.com/Continuous Current50A * 4Burst Current55A(5seconds)TVS Protective diodeYesExternal Capacitor1000uF Low ESR Capacitor(In the package)ESC ProtocolDSHOT300/600Power Input3-6S LiPoPower OutputVBATCurrent SensorSupport (Scale=386 Offset=0)ESC TelemetryNot supportedMounting30.5 x 30.5mm( 4mm hole diameter)Dimension45.6(L) * 44(W) * 6.1mm(H)Weight13.8g

Price: 41.99 USD

Location: China

End Time: 2025-01-13T16:18:18.000Z

Shipping Cost: 0 USD